Buying Guides · 6 min read · November 20, 2026

Nylon vs Polyester Putting Mats: Compare the Complete Construction

Compare nylon and polyester putting mats by face, backing and sample roll. Define the intended floor and test conditions before approving a branded bulk order.

Close-up of a green printed putting mat face with blue and yellow artwork.

Choose a construction for the intended practice task

Compare nylon and polyester putting mats as complete constructions: face, backing, finished outline and the surface beneath the mat. Request samples for the intended use and compare their roll under the same conditions. A fibre name alone is not a speed rating, and a backing name alone does not approve a mat for every floor.

Start by describing the customer’s task. A retail buyer preparing a home-practice range, a golf centre choosing a demonstration lane and a brand ordering gifts may value different combinations of roll, artwork and storage. Record the required outcome before selecting the face. This article compares construction choices and sample checks; it does not claim a measured green-speed result or a guaranteed improvement in putting performance.

Read the face and backing together

Read the face and backing together
Recorded constructionRecorded positioningConfirm before ordering
Polyester + dotted non-woven backingA faster-roll option in the recorded rangeActual sample roll and floor suitability
Nylon + TPR backingA heavier-pile, relatively slower-roll option in that rangeSelected pile and complete backing build
Polyester + TPR backingA value-oriented alternativeCurrent specification and sample comparison

These descriptions refer to the recorded product range and are scoped to the recorded combinations. They are not a rule that every nylon mat is slower than every polyester mat. Ask which configuration is currently proposed for your order. Compare it with the putting practice mat specification rather than assuming all combinations are stock items or share the same finish.

Compare sample roll on a recorded setup

Agree the comparison setup before the samples arrive: the intended floor, mat preparation, orientation, ball and the way the ball is released. Record the same conditions for each sample and inspect whether the mat lies as intended. If a supplier provides a numerical speed claim, ask how it was obtained and whether it describes the exact construction being quoted. Do not transfer another brand’s published figure.

The aim is a useful purchasing comparison, not a claim that an informal trial is a recognised laboratory test. Keep observations and measured values clearly labelled. Use the putting-mat performance selection guide to define questions, then retain the actual sample reference with the result. A video without a known setup may show a rolling ball but leave the reason for a difference unresolved.

Test the complete mat in its intended space

Check the finished width, usable putting lane and standing position together. A sample that demonstrates surface texture may not show the full edge treatment or the way the finished mat will sit in the room. Request a representative finished sample or agree which details remain untested. Include storage and the product-specific preparation instructions in the trial.

The putting-mat thickness guide addresses a different part of the specification; do not let a thickness number stand in for face-and-backing approval. For golf-centre or simulator-studio purchasing, add the actual lane and staff handling requirements. A mat that meets the preferred roll in one test still needs to fit the planned working position.

Approve printed guides separately from the material

If the mat carries aiming lines, distance marks or a logo, approve those positions on a dimensioned proof. Agree the meaning and reference point of any mark before calling it a training measurement. Check the final print on the selected face; a screen can show the layout but cannot approve the feel and roll of the finished construction.

A planning example: two samples use the same artwork, but one has a different backing. The familiar design does not make them interchangeable. Compare the complete builds and record whether the artwork and physical sample have both been accepted. This is a decision example, not a claimed customer test. Keep the sample and digital-proof sign-offs separate so a design approval cannot silently authorise a material change.

Put the comparison conditions into the enquiry

Send the customer type, intended floor, finished size, desired practice layout, branding files and order quantity. Ask for the exact face and backing, representative samples, preparation and care instructions, and evidence supporting any numerical roll claim. Request prices against named construction options so the quoted difference can be traced to something more precise than “nylon” or “polyester”.

For retail ranges, retain the approved sample and comparison notes with the product version. For branded gifts, define the physical specification as carefully as the logo file. Availability, MOQ, sample timing and delivery terms need confirmation for the selected build. When a repeat order changes face, backing or finish, review the conditions again rather than assuming an old roll observation still describes the new product.

This article is general industry guidance. For advice on a specific project, contact our team.

Related products

Let's build the right mat solution for your business

Tell us your product, market and artwork. Our team will review your request and reply with a customized solution and quotation.